Last Updated on August 5, 2023 by Mark S. Taylor
Turning or stopping a large truck or bus makes it difficult to see the car or everything behind it. On the way home or while stopped, you could damage yourself or someone else’s vehicle, injure yourself in an accident, or injure your vehicle or someone behind you. It’s too mainstream. It is recommended to install a backup camera in the parking space to avoid unnecessary trouble with the recommendation.
Contents
To install the wireless backup camera, you will need the following the kit includes:
Car Rearview Camera
Wireless RCA Video Transmitter / RCA
Wireless Video Transmitter
Avoid complicated wiring in car monitors
headphones
DVD players
cameras, etc.
Wireless-capable camera installation procedure Most cameras have a custom installation procedure. We recommend that you read the manual before install a backup camera. Wireless backup cameras are available in a variety of shapes and sizes to suit individual tastes and preferences. This is the way you choose, but you should choose a vehicle with a transparent cover and behind it.
Installation Procedure for Wireless Backup Camera
First remove the front part of the license plate lamp. Attach the rear camera to the license plate light, being careful not to damage the connecting cable & after registration, the best place is through the connecting cable of the license plate lighting system of the tail light system.
Then disconnect the license plate cable and connect the power cable and the image from the transmission system to the corresponding wireless camera cable. Do not swap the plus and minus wires. It can cause serious damage. Be careful if you have too many threads, and use locks to prevent threads from falling out. Then place the tail lights where you want them.
To transmit a signal effectively, the transmitter must be strategically placed so as not to interfere with the signal transmission. Make sure the connections are complete to avoid short circuits that can damage the entire system.
When accessing the monitor while plugged in, power is supplied from the same location as the light angled plug and the receiver plugs into the Slide T quick connector USB port. There are no leaks that drain the battery when the camera wireless back is not in use.
Once the installation is complete, all camera features such as the effectiveness of the camera’s field of view and camera positioning should be tested. This must be done in standby mode.
The wireless kit on the back contains supporting hardware, including a wireless backup camera. The camera’s signal transmission system, the receiving system next to the monitor, the car converter needed to operate the entire system, the adapter cable used to view the image from the rear of the vehicle, and the monitor from your car.
Installation Procedure for Wired Camera
Part 1
Buy a rear-view camera for your car. For safety reasons, buy a device designed specifically as a reversing camera. Buying a device designed for a specific vehicle makes it easier to install than a standard service camera. Locate the camera on the license plate or on the back for easy installation. Find a backup camera at any consumer electronics store.
If you want to keep your old rearview mirror, buy an external monitor. An external backup monitor is a small video monitor that attaches to the windshield like a GPS glass. It takes up more space than an integrated monitor, but it’s easy to see and can be easily replaced if needed. A standard video monitor can be used instead if desired. However, there may be similar hardware features designed for use with a rear camera.
Buy an internal monitor for a device that isn’t boring. The inner back plate is a full-featured mirror with a small glass screen. Some internal fenders are attached to the rearview mirror and others completely replace the main rearview mirror. Most of the interior panels are sealed and removed when not in use, making them an ideal choice if you want to preserve the look of your car.
If your camera and monitor don’t have power and video cables, buy one. Most rear camera installations require a camera splitter and monitor cable connected to the video and power cables, two wired power cables, and a video sync cable. Most installation kits include these cables, but some must be purchased separately. Some camera models use a wireless transmitter instead of a standard video cable.
Part 2
Remove the back plate. Using a Phillips screwdriver, remove the two screws holding the back plate in place. Then take out the card and set it aside. Keep the screws in a safe place to avoid losing them.
Remove the inner lining from the bag. Open the trunk and find the sturdy inner cover that covers the other side of the license plate mounting area. Then place a lawnmower or other thin device behind the screen and open it. Remove this panel to reveal the rear cable compartment of the vehicle.
Make a small hole in the plate. Make sure there are no obstructions between the license plate holder and the rear wiring. Then use an electric drill and a quick drill to make small holes in the car. Adjust the hole so that the power cord and film are behind where they connect to the camera.
Go to the location where you want to mount the camera to see the drilling.
Next, check where the gap wire is. Drill a hole large enough for the video and device power cables.
When you encounter obstacles, try to overcome them. If you can’t, see if you can drill a hole nearby. Most jobs will require a drill bit 1-2 inches (0.32-0.64 cm) in diameter.
Place a rubber band around the camera cable. Place the rubber ring on the free end before connecting the camera cable to the vehicle. These small rubber washers, available at most hardware stores, hold wires in place to prevent leaks. Choose a shirt that is large enough to fit into the pit.
Thread the camera cable into the trunk of the car. Disconnect the removed camera end and camera power cord from the hole in the trunk. Only nail the rear and side pallets, not the front. The camera cable must be routed from the outside of the vehicle to the inside of the vehicle.
Determine the vehicle backlight wiring. The reverse cable is the light that connects the car’s tail light to the dashboard. They attach directly to the car’s taillights and can usually be found in the tailgate or trunk. This rope varies from vehicle to vehicle. So, if you can’t find it, check your user manual for model information.
Remove the cable from the car’s tail light. Loosen the rubber covering the thread using a wire cutter or pliers. Then use a screwdriver or other thin tool to drill a hole in the center of each wire and separate the wires. For safety, do this with the vehicle turned off.
Fasten the camera cable to the backlight cable. Connect one of the exposed wires to the power cord of the camera cable. Then place the exposed wire in the center of the extra light wire and twist. Wrap electrical tape around the internal wiring for additional protection. The bare positive (usually red) wire must be connected to the positive reverse positive wire and the exposed negative (usually black) wire must be connected to the bright negative wire.
Part 3
Thread the camera film cable through the front of the vehicle. If necessary, connect the RCA cable to the video connector on the camera cable. Then move it next to the car’s fuse box. Depending on the car model, this can usually be done by pulling the car’s trim or side panels and pulling the cables out of the visible case. Some trucks may require the video cable to run through a rubber wall. Most cars have a fuse box under the steering wheel.
Connect an external monitor to the windshield. When installing an external monitor, first install the units guide foot on the windshield according to the manufacturer’s instructions. Then connect the monitor to the base. Most external monitors use vacuum cleaners, but some have more sophisticated installation systems.
Attach the built-in monitor to a mirror or mirror stand. Some integrated monitors require a new monitor installed in the existing rearview mirror. Others have to remove the mirror and slide the screen according to the mirror they already own. Some interior panels may have their own mounting system that must be mounted to the windshield.
Route the cables from the slots in the shield to the fuse box. Connect power and video cables to the projector, if necessary. Then connect the monitor cable to the side of the fuse box. If necessary, use the discolor tool to remove the bus front panel just above the windshield. Then thread the cable through the exposed case.
Connect the monitor camera cable to the RCA cable. After laying the screen divider cable, connect the film end of the cable to the camera cinch cable. Then wrap the connected wires with electrical tape and secure them together. You may need to purchase a male and female RCA adapter cable if the RCA and video cables have the same ends. You can find it in most electronics stores.
Connect the monitor power cable to the safety valve. Connect the remaining cables to the monitor’s redundant power cable. Then slide the positive (usually red) end of the exposed wire rope towards the open end of the safety valve. Finally, glue the two cables together with pliers. A fuse tube is a short wire that converts an exposed wire into a signal fuse. You can find it at most auto parts stores. If you prefer, you can leave the power cord turned off and connect the camera power cord to the cigarette lighter adapter. Then connect the adapter to your car’s cigarette lighter.
Connect the safety valve to the fuse box. Find the fuse box and open it. Then connect the safety valve to the open safety cell. If necessary, check the fuse box cover or vehicle manual for any discrepancies. After connecting the fuses, connect all wires together to avoid loosening.
Part 4
Connect the rear camera to the power and video cables. After installing the rear-view monitor and all necessary camera cables, return to the vehicle. If necessary, turn off the trunk and connect the rear camera to the power cable and film. The camera power and video cables should come out of the holes in the license plate.
Secure the camera to the license plate. If the camera is mounted in front of the license plate, follow the manufacturer’s instructions to mount the camera to the screen. With the camera mounted on the back of the license plate, align the hardware with the mounting holes on the screen and secure with screws. In most cases, the rear camera can be mounted on the back of the license plate by unscrewing it from the vehicle.
Reinstall the license plate and pairing. Replace the rear license plate using a Phillips screwdriver. After reassembling the engine, prepare the license plate and rear-view camera to make sure it is safe. If not already fitted, replace the rear panel and other panels by sliding them into the vehicle.
Test your camera to make sure everything works. Test your new camera in a safe place like yours before using it on public roads. In this case, check for image distortion by placing a large, hard object, such as a trash can, behind the camera. If it does not turn on, see the installation guide for troubleshooting information. Rear camera errors are often caused by loose cables or incorrect connections.
Frequently Asked Questions For install a backup camera
Are wireless backup cameras easy to install?
Ans: Wireless cameras are easy to set up as there are no wires or cables to connect the camera to the monitor (there may still be cables to connect the power to), but the connection is poor. Poor connection, especially when there is little or no water. Bad weather can be erratic.
Do wireless backup cameras work well?
Ans: Some wireless backup cameras provide a more stable digital signal, but can cause problems. … when the rear camera transmits video data wirelessly to the monitor, interference, delay, or overall picture quality degradation may occur depending on the signal strength.
Can you have two backup cameras?
Ans: Obviously you want to use multiple cameras. …for this reason, we recommend the Swift Hitch 2 Camera System # SH03D, which allows you to view images from two different cameras (including) on the same monitor on the system.
